Pengaruh Radius Mooring Line Terhadap Penambatan Fpso Menggunakan Pendekatan Numerik

Adhitya Arya Prayudha Kurniawan

doi:10.62012/zl.v5i1.31724

Authors

Adhitya Arya Prayudha Kurniawan Department of Ocean Engineering, Faculty of Engineering, Hasanuddin University, Indonesia

DOI:

https://doi.org/10.62012/zl.v5i1.31724

Keywords:

Floating Production Storage and Offloading (FPSO), Mooring Line, Tension

Abstract

Floating Production Storage and Offloading (FPSO) is a floating facility in the form of a ship that is used to produce as well as a temporary storage of petroleum taken in the middle of the ocean, in its operation the FPSO is moored using mooring ropes to limit the motion of the facility. This mooring system is needed to reduce dynamic movements due to environmental loads received by the FPSO. This study was conducted to analyze the motion characteristics of FPSO that have been moored using a Spread Mooring System with a certain mooring radius and the stresses received by each mooring line using a time domain based numerical approach. The method used is a literature study and a numerical approach with the Boundary Element Method (BEM), it is concluded that the further the radius of the mooring line, the smaller the tension received by each mooring rope so that the structure becomes more stable.

Downloads

Download data is not yet available.

References

A. H. Fajar, D. Chrismianto, dan E. S. Hadi, “Studi Analisa Slamming & Deck Wetness Akibat Gerakan Heaving – Pitching Coupling & Gerakan Non-Linier Rolling (Studi Kasus Kapal MT. Pandan),” Jurnal Teknik Perkapalan,Vol. 5, Universitas Diponegoro, 2017.

B. Hariyanto, “Analisis Tegangan Mooring Line Pada Single Point Mooring Calm Bouy Cilacap,” Departemen Teknik Kelautan, Institut Teknologi Sepuluh Nopember Surabaya, 2018

B. Purnama and F. M. Assidiq, “Numerical Studies Fatigue Damage From Material Variations Catenary Mooring System FPSO Al Zaafarana”, Journal of Maritime Technology and Society, vol. 3, no. 1, pp. 52-62, Feb. 2024.

F. M. Assidiq, D. Paroka, M. Z. M. Alie, dan Syerly Klara, “Fatigue Analysis Of Catenary Mooring System due to Harsh Environment in Head Seas,” EPI int. Journal of Engineering, Vol.1, 2018.

N. S. Aulia and F. M. Assidiq, “Comparative Numerical Analysis Fatigue Damage Based On Variation In Quantities Mooring Line On Aker Smart 2 FPSO”, Journal of Maritime Technology and Society, vol. 3, no. 1, pp. 21-32, Feb. 2024.

M. I. Afdhal, B. Untung dan I. P. Mulyatno, “Optimasi Disain Spread Mooring Dengan Konfigurasi Variasi Line Terhadap Six Degrees Of Freedom (DOF) Olah Gerak Pada Kapal Floating Storage And Offloading (FSO),” Jurnal Teknik Perkapalan,Vol. 7, Universitas Diponegoro, 2019.

A. E. Ramadani and F. M. Assidiq, “Analysis of The Effect of mooring Depth & Fatigue Damage on Mooring Line FPSO Ship Azurite In The Masela Block”, Journal of Maritime Technology and Society, vol. 3, no. 1, pp. 33-42, Feb. 2024.

S. Saparuddin and F. M. Assidiq, “Analysis of Motion and Mooring of Fpso Vessels Due to Different Types of Mooring Material”, Journal of Maritime Technology and Society, vol. 3, no. 1, pp. 12-20, Feb. 2024.

F. Julyardiansyah and F. M. Assidiq, “Configuration Comparison Catenary Spread Mooring Line On The Movement Characteristics Of Fpso Ships Using Numerical Analysis”, Journal of Maritime Technology and Society, vol. 3, no. 1, pp. 1-11, Feb. 2024.